Equipment needed:
1. Two or more PCs
2. Network Card according to number of PCs
3. Coaxial cable or UTP
4. Hub when needed
5. Terminator
6. T-Connector
Manufacturing steps:
1. First you need to know in advance the type of network you want to use. When this type of network that is often used is the bus type and the type of star.
1.1 Type of Bus
This type of network connects directly from komp1 to komp2 ago komp2 to komp3 ff. This type of network is the most easy installation and cheaper so more suitable for the home user, while it has the disadvantage that if there is one comp is broken it will affect the other comp. This type of network using coaxial cable that we often encounter in the antenna cable tv.
1.2 Type of Star
Each computer on the network is directly connected to each hub using UTP cable type that resembles a telephone cable. For example komp1 to komp2 to HUB and HUB. Of HUB then connected to a computer acting as a server. Between HUB can also be connected such that the snooze HUB1 dr komp1 and komp2 associated with the snooze HUB2 komp3 and komp4 dr. Likewise, if we want to put on some servers, such as HUB snooze from server1 and server2 connected to Server3 that acts as the primary server.
2. Attach the cable and network cards. Adjusted cabling topology / network type you choose, while the selection of network cards tailored to the existing slot on your motherboard. If your board has a PCI slot then it's better because LAN cards based on PCI bus is faster in data transfer.
3. If you use the bus type on each computer you need to install the Q-Connector has two inputs. And on a computer that only gets 1 input on both the input terminator should be installed unless you make a circle-shaped network (circle) where all computers got 2 inputs. For example komp1, komp2, komp3 lined the t-conncector on komp1 mounted terminator and cable to komp2. Komp2 mounted on wires and cables to the dr komp1 komp3. While komp3 installed cable and terminator komp2 dr.
4. When you select the type of star that each cable from the computer put into anavailable port on the hub. And if you want to connect the hub to the other hubs you are using UTP cables are inserted into the existing special port on each hub.
1. Two or more PCs
2. Network Card according to number of PCs
3. Coaxial cable or UTP
4. Hub when needed
5. Terminator
6. T-Connector
Manufacturing steps:
1. First you need to know in advance the type of network you want to use. When this type of network that is often used is the bus type and the type of star.
1.1 Type of Bus
This type of network connects directly from komp1 to komp2 ago komp2 to komp3 ff. This type of network is the most easy installation and cheaper so more suitable for the home user, while it has the disadvantage that if there is one comp is broken it will affect the other comp. This type of network using coaxial cable that we often encounter in the antenna cable tv.
1.2 Type of Star
Each computer on the network is directly connected to each hub using UTP cable type that resembles a telephone cable. For example komp1 to komp2 to HUB and HUB. Of HUB then connected to a computer acting as a server. Between HUB can also be connected such that the snooze HUB1 dr komp1 and komp2 associated with the snooze HUB2 komp3 and komp4 dr. Likewise, if we want to put on some servers, such as HUB snooze from server1 and server2 connected to Server3 that acts as the primary server.
2. Attach the cable and network cards. Adjusted cabling topology / network type you choose, while the selection of network cards tailored to the existing slot on your motherboard. If your board has a PCI slot then it's better because LAN cards based on PCI bus is faster in data transfer.
3. If you use the bus type on each computer you need to install the Q-Connector has two inputs. And on a computer that only gets 1 input on both the input terminator should be installed unless you make a circle-shaped network (circle) where all computers got 2 inputs. For example komp1, komp2, komp3 lined the t-conncector on komp1 mounted terminator and cable to komp2. Komp2 mounted on wires and cables to the dr komp1 komp3. While komp3 installed cable and terminator komp2 dr.
4. When you select the type of star that each cable from the computer put into anavailable port on the hub. And if you want to connect the hub to the other hubs you are using UTP cables are inserted into the existing special port on each hub.
0 comments:
Post a Comment